Command |
Description |
Ctrl+L |
Form Feedformfeed. |
Esc C (n) |
Set page length in n lines. |
Esc C Ctrl+@ (n) |
Set page length in n inches. |
Esc N (n) |
Set skip over Perforation |
Esc O |
Cancel skip over Perforation. |
Ctrl+J |
Line Feed. |
Esc + (n) |
Set n/360-inch line spacing. |
Esc 0 |
Select 1/8-inch line spacing. |
Esc 2 |
Select 1/6-inch line spacing. |
Esc 3 |
Set n/180-inch line spacing. |
Esc A |
Set n/60-inch line spacing. |
Esc J |
Perform n/180-inch Line Feed. |
Ctrl+K |
Tab vertically. |
Esc B (n1) (n2) ... Ctrl+@ |
Set vertical tabs at n1, n2
positions. Esc B Ctrl+@ clears all tabs. |
Esc b (c) (n1) (n2) ... Ctrl+@ |
Set vertical tabs in channels.
c=channel atn1, n2 positions. Esc b (c) Ctrl+@
clearstabs in channel c. |
Esc / (c) |
Select vertical Tab channel. Set Tab
channelto c. |
Command |
Description |
Esc E |
Select emphasized mode. |
Esc F |
Cancel emphasized mode. |
Esc G |
Select double-strike mode. |
Esc H |
Cancel double-strike mode. |
Esc S Ctrl+@ |
Select Superscriptsuperscript mode. |
Esc S Ctrl+A |
Select Subscriptsubscript mode. |
Esc T |
Cancel
Superscriptsuperscript/Subscriptsubscript mode. |
Esc ( - (n1) (n2) (m) (d1) (d2) |
Select score.
n1=Ctrl+C
n2=Ctrl+@
m=Ctrl+A
d1 values:
Ctrl+A: underline
Ctrl+B: strike-through
Ctrl+C: overscore
d2 values:
Ctrl+@: Cancel the score line selected by d1
Ctrl+A: Single continuous line.
Ctrl+B: Double continuous line.
Ctrl+E: Single broken line.
Ctrl+F: Double broken line.
|
Esc - (n) |
Turn under line mode
ON(n=Ctrl+A)/OFF(n=Ctrl+@). |
Esc q (n) |
Select Character Stylestyle.
n values:
Ctrl+@: normal
Ctrl+A: Outlineoutline
Ctrl+B: shadow
Ctrl+C: Outlineoutline with shadow
|
Command |
Description |
Esc K (n1) (n2) |
Select single-density graphics mode. |
Esc L (n1) (n2) |
Select double-density graphics mode. |
Esc Y (n1) (n2) |
Select high-speed double-density
graphics mode. |
Esc Z (n1) (n2) |
Select quadruple-density graphics
mode. |
Esc * (m) (n1) (n2) |
Select graphics mode.
m values:
Ctrl+@: single-density 8 pin
Ctrl+A: double density 8 pin
Ctrl+B: high speed double- density 8 pin
Ctrl+C: quadruple density 8 pin
Ctrl+D: CRT I 8 pin
Ctrl+F: CRT II 8 pin
Space: single-density 24 pin
a: double-density 24 pin
g: CRT III 24 pin
h: triple-density 24 pin
i: hex-density 24 pin
|
Esc ? (s) (m) |
Reassign graphics mode. S values
are(K,L,Y,Z) above. M values same as Esc *m options. |
Note: The P2 command set includes all other N9 ROM
commands as well as the following new commands:
Command |
Description |
Esc ( c Ctrl+D Ctrl+@ (m1) (m2) (n1)
(n2) |
Set page format. M is top Margin in
definedunits. N is bottom Margin in defined units. |
Esc ( C Ctrl+B Ctrl+@ (n1) (n2) |
Set page length in defined n units. |
Esc ( V Ctrl+B Ctrl+@ (n1) (n2) |
Set absolute vertical print
position. N specifies print position from top Margin
indefined units. |
Esc ( v Ctrl+B Ctrl+@(n1) (n2) |
Set relative vertical print
position. N movescurrent print position in defined
units. |
Esc X (m) (n1) (n2) |
Select Font by Pitchpitch and
Pointpoint. M sets pitchto 360/m CPIcpi. N sets
Pointpoint size in 0.5 pointincrements. |
Esc ( U Ctrl+A Ctrl+@ (n) |
Define unit for spacing. N is
positioningunit as n/3600 inch. |
Esc ( t Ctrl+C Ctrl+@ (d1) (d2) (d3) |
Assign Character table set by d2 and
d3 tod1. |
Esc ( ^ (n1) (n2) (data) |
Print data as characters. N is the
amount ofdata and Data is the n byte data for
printingas Character. |
Esc ( G Ctrl+A Ctrl+@ (n) |
Select graphics mode. |
Esc . (c) (v) (h) (m) (n1) (n2) |
Print Raster Graphicsrastergr.
c values:
Ctrl+@: full graphics mode
Ctrl+A: compressed mode
v is the vertical dot density in 3600/v DPIdpi
h is the horizontal dot density in 3600/h DPIdpi
m is the number of vertical dots
n is the number of horizontal dots
|